WASHING MACHINE FOR HAMS OF SLAUGHTER HOOKS Type MH-600S
WASHING MACHINES FOR HAMS OF SLAUGHTER HOOKS
MH 600S

Application

MH 600S is a specialist device designed for cleaning all types of hooks used for slaughtering pigs made of stainless steel with a total length of 515 mm, of which a 225 mm length hook with a capacity of up to 600 pieces / h is subjected to a washing process.

Transport hooks:

Transport of hooks in the washing process takes place automatically from the side of the main washing zone, and the exit from the side of the rinsing zone with hot water at 85 C, thus working in line with a continuous transport system in a closed circuit.

The washing speed is constant depending on the slaughter performance of the line.

The main washing process:

The main wash zone is divided into main washing and rinsing sections and sterilization with hot running water at 85 ° C from the factory network. The washing process in the main washing section takes place in a closed cycle with the addition of a cleaning agent to assist washing. The detergent is automatically dispensed by means of a pump with conductometric measurement directly to the main wash water tank. In addition, the water temperature during washing is automatically regulated and maintained. The accuracy, efficiency and efficiency of cleaning the hooks guarantees the use of stainless steel nozzles with a constant angle of washing and adequate water flow. The factor supporting the process of thoroughly cleaning the hooks is the constant speed on the slaughter line. What's more, the device has a filtration system. The overflow filter collects floating floating water on the surface of the tank, eliminating them directly into the drain in the floor. Filter drawer ring, stops solid contaminants, protecting the washing nozzles from clogging, which guarantees the effectiveness of cleaning. The introduced water management in the washer ensures that the water in the main washing tank is properly refreshed.

The final rinsing process:

The final rinsing process is carried out using running water from the hot water network at 85 C. The rinsing ring is equipped with stainless steel nozzles with a suitable water flow and angle of rinsing. The water after rinsing the hooks flows into the common water management in the washer, where it is divided appropriately and delivered to the water reservoir set on the floor, in order to refresh it.

Construction:

The closed design ensures full safety of operators who are working during operation. In addition, the use of a through-going structure allows the device to be located in the dirty zone, and the washed hooks go directly to the slaughter line. Made of stainless steel ensures high hygienic conditions. In addition, the readable control panel allows full control of the washer's operator over the washing process. In our devices we use proven components from renowned companies and modern solutions aimed at reducing the maintenance costs of our devices to a minimum. The introduction of modern water management significantly reduces the costs of using the washer in terms of water and energy consumption, cleaning agents, sewage discharge to the sewage system.

The most important advantages of the structure:

Operation of the device is maintenance-free
Construction made of stainless steel
Reducing to a minimum the consumption of water and detergent by introducing proper water management in the washer
High performance sanitary water pump
Basic washing section
Rinsing and disinfection section with running water at 85 ° C
Closed water circuits in the main and washing zones
Adjustable water used for rinsing
Constant speed of the slaughter line
Functional design
Delta electronic control

Basic technical data:

Type

MH 600S

Washing chamber

Length

3000 mm

Width

640 mm

Height

650 mm

The base of the washer

Length

2500 mm

Width

1175 mm

Height

975 mm

Tank with pump and control

Embedded on the floor

Weight

480 kg

Power supply voltage

3 x 400 V

Total power

7.5 kW

Water supply

1”

Water drain from the washing machine

 2"

Steam connection

1” DN 25 /3-6 bar/

Compressed air connection

Ø8 mm 6-8 bar

Ventilation chimney

2 x 200 mm

 Main wash zone

MH 600S

Pump performance

1 x 40 m3/ h

Number of washing nozzles

48 pcs. Of stainless steel with a fixed washing angle

Overflow filter

It collects excess water, fat, resulting foam

Filter drawer eye

A mesh clearance of 2 mm

It eliminates permanent dirt

Tank capacity

450 l

Water heating in the tank

The circuit is closed through the coil by steam

Transport hooks

On the existing slaughter line

Dosing chemical agent

With conductometric measurement

 

Rinsing and disinfection zone

MH 600S

Border

3 adjustable water flow

The number of rinsing nozzles

3 x 4 x 1.9 l

Pressure at the entrance

2-3 bar from the 85 C hot network

Drainage

For the water management system

CALL ME
+
Call me!
Chemaxpol - a clean business website
en_GB
pl_PL en_GB